Doors lie flat in a filtered booth off site, and boxes are finished at home inside sealed containment. Thin passes, sanded between, give the level hard surface that separates sprayed cabinet painting from brushwork.
Markham houses are large and their kitchens carry a lot of doors, so the difference between a sprayed finish and a brushed one is on display across a wide surface. In condo units around Enterprise Boulevard there is a second reason: buildings restrict on-site spraying, which makes shop work the only practical route.
A Brush Leaves Ridges That Never Sand Out
Enamel dragged from a brush sets with lap lines and ridges across a shaker panel, and a roller leaves a fine stipple that catches light from the side. Neither reads as a factory finish and both trap dirt in the texture, which is why brushed cabinet painting looks tired years before sprayed work does. Spraying atomises the coating into an even film that flows out before it sets, which is the whole basis of sprayed cabinet painting.
The trade-off is preparation. Spraying demands masking, containment, extraction and booth space for every door, and that setup is why sprayed cabinet painting carries more labour than brushing. What it returns is a surface that wipes clean and holds up at the pulls and the cutlery drawer.
Doors Go To The Booth And Boxes Stay In The Kitchen
Each drawer front and each door is tagged, taken off, racked and driven to a filtered, temperature-controlled booth, where it is sprayed lying flat. Flat cabinet painting matters because gravity then helps a coating level out instead of dragging it down a standing face.
Face frames and boxes cannot leave the room, so they are coated in position inside sealed plastic, with openings taped and floors covered. Containment of that kind is what allows cabinet painting in an occupied house without dust reaching the rest of the level. Fixed cabinetry elsewhere in the home is handled the same way, as the pantry, laundry and built-in page explains.
Several Thin Coats Beat One Thick Coat Every Time
Two coating families do the cabinet painting work. Waterborne alkyd enamel levels well, tints to almost any colour and cures slowly to a hard film. Two-part 2K polyurethane, mixed with a hardener and applied only by gun, cures faster and resists cleaners and daily wear better, which is why factory cabinets carry it.
Either one is sprayed in a few thin passes, lightly sanded between. A single heavy coat looks faster and fails earlier, because the top skins over while everything below it stays soft. Thin sprayed cabinet painting is the reason a good kitchen still looks new at year eight.
Cure Time Decides When Ordinary Kitchen Use Can Resume
Sprayed cabinet painting will take handling in a few days, ordinary use around the one-week mark, and full hardness near the end of the month. A 2K system gets most of the way there within about two days. Doors go back up once they can be handled safely, and the written care notes explain what gentle use means through the remainder of the cure. Markham summers sit near sixty per cent indoor humidity, which slows waterborne coatings, so the cabinet painting timetable allows for that instead of rushing a recoat.
Ask What Sprayed Cabinet Painting Would Cost Here
Spraying is built into every kitchen we quote rather than sold on top. Send the form or call +1 (289) 201-7026, giving the door count and, for a condo, the building, and a free visit follows. Everything else we handle across Markham, Unionville and Cornell sits on the Markham Cabinet Painting home page.
Cabinet Spray Painting Questions
Why spray cabinets instead of brushing them?
A brush leaves ridges and a roller leaves stipple, and both trap dirt in the texture. Spraying atomises the coating into an even film that flows out flat before it sets, which gives a hard surface that wipes clean.
Does the spraying happen in my house?
Doors and drawer fronts are sprayed flat in a filtered booth off site. Face frames and boxes are coated in place inside sealed plastic with the openings taped, so dust and overspray stay out of the rest of the house.
How long until the finish is hard?
Handling is safe in a few days, ordinary use comes about a week later and full hardness near the end of the month. A 2K polyurethane gets most of the way in about two days. Humid summers slow waterborne coatings, so the timetable allows for it.